How much concrete should you order?
A measurement checklist for turning pour dimensions into a practical material order.
1. Split the project into measurable pours
Measure the inside dimensions of each form or excavation at the size you expect to fill. A slab, thickened edge, footing and post hole may need different formulas. Keep them separate, then add the volumes. The multi-pour calculator handles rectangular and round areas in one estimate.
For irregular slabs, divide the outline into simple rectangles that do not overlap. Measure each rectangle, calculate its volume and sum them. For sloped or uneven excavations, take several depth readings; a single shallow reading can understate the volume.
2. Check the exact volume before adding extra
A 10 ft × 10 ft slab at 4 in thick has 10 × 10 × (4 ÷ 12) = 33.33 cubic feet. Dividing by 27 gives 1.23 cubic yards. This is the geometric volume. A 10% allowance makes the planning order 36.67 cubic feet, or 1.36 cubic yards. The allowance is an input you can change, not a universal rule.
If a footing trench is wider than the plan or a slab base is low in places, remeasure it. A percentage cannot reliably correct a known dimensional error.
3. Compare bags and ready-mix using the same volume
Concrete bags are purchased by whole units. At an approximate yield of 0.60 cubic feet per 80 lb bag, the example above needs 36.67 ÷ 0.60 = 61.11, rounded up to 62 bags. That is 4,960 lb of dry bagged material to move and mix. The bag calculator also supports 40 and 60 lb bags.
Ready-mix is ordered by volume. Ask local suppliers about their minimum order, short-load fee, delivery access and order increments. Compare the delivered quote with the bag cost and the work involved; this site does not assume one purchasing method is always cheaper.
4. Confirm the details with your supplier
- Give the measured dimensions, number of pours and target order volume.
- Confirm the actual yield on the bag or product sheet; specialty mixes can differ.
- Ask about delivery minimums, truck access, unloading time and any extra fees.
- Use the mix specification in the plans; this calculator does not select strength or design reinforcement.
- Recheck dimensions after forms and excavation are complete, before placing the final order.
Common measurement errors
Mixing inches and feet without conversion, counting overlapping areas twice, using outside form dimensions instead of fill dimensions, and rounding each small pour before adding them can all skew an estimate. pourmeasure sums unrounded geometric volumes and rounds only the displayed result and final bag count. The methodology page lists conversion factors and source yields.
Example order reconciliation
A 12 × 16 ft slab at 4 in needs 64 ft³, or 2.37 yd³ exact. Add a non-overlapping 4 × 5 ft landing at 6 in: another 10 ft³. The combined exact volume is 74 ft³, or 2.74 yd³. At 10% extra it becomes 3.01 yd³; a supplier selling in half-yard increments might quote 3.5 yd³. Check whether a smaller increment is available before accepting the rounded order.
Keep an order record
Save the labeled measurements, calculation date, product or mix specification, quoted order increment, delivery access notes and itemized price. Share the same version with the crew and supplier. If forms change after the quote, recalculate rather than relying on the old quantity. This record makes it possible to distinguish a measurement change from a supplier minimum or a material-yield difference.
A slab and footing combined order
A 12 × 16 ft slab at 4 in is 64 ft³. A separate 20 × 2 ft footing at 12 in depth is 40 ft³, assuming the footing does not overlap the counted slab volume. Together they need 104 ft³, or 3.85 yd³ exact. Ten percent extra produces 114.4 ft³ or 4.24 yd³. A supplier selling in half-yard increments might bill 4.5 yd³. If the footing shares a portion of the slab geometry, adjust the sketch and subtract the overlap before making this order.
Compare bags to the same planning volume
At 114.4 ft³ and 0.60 ft³ finished yield per referenced 80 lb bag, the combined job takes 191 whole bags. Those bags weigh 15,280 lb dry. That amount may make repeated mixing and transport difficult, but the actual decision depends on site access, mix requirements, labor and delivered ready-mix fees. Ask for an itemized supplier quote rather than assuming the per-yard material rate is the total cost.
Useful questions
Do the measurements match built forms? Are footing and slab volumes non-overlapping? What product or ready-mix specification is required? What is the supplier increment and minimum load? Are delivery, pumping and taxes included? Where will the truck stop, and who is responsible for placement and curing? Keep the written answers with the estimate link or printed calculation.
Questions before you decide
Should I round each pour separately?
If all pours are part of one order, add their exact non-overlapping volumes first, apply the selected allowance, and then follow the supplier’s increment. Separate delivery dates or mixes may require separate orders. Ask the supplier how they handle each load.
What belongs in a supplier quote?
At minimum, confirm mix specification, billed quantity, unit price, delivery charge, small-load or waiting fees, taxes, delivery window and discharge assumptions. Pumping or long-distance placement may be separate. Keep the written quote with the measurement sheet.
Can a calculator replace the final site check?
No. The calculator computes from entered dimensions. Forms, openings, base elevations and project details must be verified on site. A final measurement check before booking helps catch changes that happened after the original estimate.
A final call checklist
Read the order back using explicit units: cubic yards or cubic meters, not just a number. Confirm the mix or bag product, calculated exact quantity, selected allowance, billed increment, delivery time, address, access point and quoted fees. Ask what happens if the truck must wait or cannot reach the forms. Record the name of the person confirming the order and the quote date. If any dimension changes afterward, tell the supplier and crew before placement; do not assume a saved estimate link updates a booked order.
After the quote arrives
Compare the supplier’s billed amount with the measured planning amount line by line. A higher quoted quantity may reflect rounding or a minimum rather than an arithmetic error. A lower quantity may indicate that the quote ignored extra allowance or one of the shapes. Check which case applies before accepting or revising the order. Save the written quote beside the labeled sketch and calculation. This protects the clarity of the estimate even if prices, delivery dates or site access change later.
Content and calculator by pourmeasure. Formula and assumption notes: methodology and sources. Updated October 2026. No independent engineering review is claimed.